He has 17 years of research experience in the development, application, and evaluation of databases, methods and models to assess the exposure, hazard, and risk of organic chemicals to humans and the environment. His research has focused on the application of high-throughput screening methods for prioritizing chemicals for risk assessment. He is the principal investigator or co-investigator of various international projects including collaborations in the United States, Europe, and Canada. He was the recipient of the James M.
In this context of changing and challenging market requirements, Gas Insulated Substation GIS has found a broad range of applications in power systems for more than two decades because of its high reliability, easy maintenance and small ground space requirement etc.
SF6 has been of considerable technological interest as an insulation medium in GIS because of its superior insulating properties, high dielectric strength at relatively low pressure and its thermal and chemical stability. SF6 is generally found to be very sensitive to field perturbations such as those caused by conductor surface imperfections and by conducting particle contaminants.
The presence of contamination can therefore be a problem with gas insulated substations operating at high fields. If the effects of these particles could be eliminated, then this would improve the reliability of compressed gas insulated substation.
It would also offer the possibility of operating at higher fields to affect a potential reduction in the GIS size with subsequent savings in the cost of manufacture and installation.
The purpose of this paper is to develop techniques, which will formulate the basic equations that will govern the movement of metallic particles like aluminum, copper in a coated as well as uncoated busduct. In recent years, the areas of industrial application of AC drives, especially Induction machine based on DTC technique has gradually increased due to its advantages over the other techniques of control.
However conventional DTC suffers from high torque ripple and variable switching frequency. This paper, propose a method to reduce torque fluctuations, where the circular flux vector is divided into twelve sectors and is compared with conventional DTC method where the flux vector is divided into six.
Electrical and Electronic Engineering Vol. F and Sansui H, "Simulink model of direct torque control of Induction machine", American journal of applied sciences 5 8: Krishnan, Electric Motor Drives: Enhancing Reusability of Conventional Apollo Modules by proposing change in design and use of new ablative material Enhancing Reusability of Conventional Apollo Modules by proposing change in design and use of new ablative material Abstract: The paper deals with the reusability of command modules used during Apollo space missions.
During Apollo missions in 's the module surface becomes charred up to some extent, hence decreasing the strength and scope of further reusability of the module. A new design has been proposed and simulation results have revealed the possibility to reuse the module again for another mission.
The new design has incorporated an in-built mechanism that will extend some part of the module surface outwards near to the periphery of the base of the module.
The design, mechanism, material and other details are discussed in succeeding sections. New ablative material has been introduced for more getting more promising results. Design patterns have been the target of a great deal of research in the last few years.
A design pattern is a general solution to a commonly occurring problem. They are composed of three parts: This paper concentrates on developing a catalog for design patterns for safety-critical real-time systems and allows flexibility to choose, search a design pattern and add more design patterns.
This tool will be able to help generate the code for the suitable design pattern.
Edition published in Safety assessment of design patterns for safety-critical embedded systems. Sarma, Sahith Rampelli, Dr. High-resolution signal parameter estimation is a significant problem in many signal processing applications.
A. International Symposia A2. Fate and Transport of Pollutants in the Environment in Honour of Don Mackay Jon Arnot, ARC Arnot Research & Consulting and University of Toronto Bio: Jon Arnot is the President of ARC Arnot Research & Consulting and an adjunct professor in the Department of Physical and Environmental Science and in the Department of Pharmacology and Toxicology at the University . Mar 02, · The case involves the placement of a new brand, Tata Nano. The car was widely touted as the cheapest car in the world to Rs.1 lakh. Students should note the difference between the ultimate goal, the huge emerging middle class Indian consumer and the available capacity and distribution in choosing a limited objective. Tata Nano - The Peoples Car Case Solution, The case is being investigated, such as Tata Motors, India's largest automobile manufacturer, the Nano, developed the world's cheapest car. The case focuse.
Such applications include direction of arrival DOA estimation for narrow band signals and wideband signal emitted by multiple sources and received by sensor arrays. Strong consistency of the modified method is established. However, an important disadvantage of the ULA geometry in DOA estimation is that it can only estimate the azimuth angle.
To estimate the elevation angle, Uniform circular arrays UCA geometries and planner array are employed in many applications.
Schmidt, "Multiple emitter location and signal parameter estimation". Antennas and Propagation, vol. A Face recognition scheme using hybrid approach is proposed in this paper. Feature vector based on eigen vectors of sub images is used for recognition Image is partitioned in to sub images.
Sub parts are rearranged in to rows and column matrices. Eigenvectors are computed for these matrices. Global feature vector is generated and used for face recognition.
Experiments performed on benchmark face database YALE Indicated that the proposed hybrid approach has better recognition performance in terms of average recognized rate and retrieval time compared to existing methods.
Pentland, Facerecognition using eigenfaces, in: Sejnowski, Independent component representation for face recognition, in: Neural Networks 13 6 — Forging is a forming method without any chips development, which is mainly used for serial produced machine parts with improved mechanical properties.Hearty Congratulations!!
Modern College of Arts, Science and Commerce, Ganeshkhind, Pune is awarded with 'STAR STATUS' by The Department of Biotechnology (DBT), Ministry of Science and Technology, Government of India.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research. Dec 01, · In , Apple introduced the iPod with the iTunes store, revolutionizing portable entertainment, creating a new market, and transforming the company.
Tata Nano - The Peoples Car Case Solution,Tata Nano - The Peoples Car Case Analysis, Tata Nano - The Peoples Car Case Study Solution, The case is considered as Tata Motors, India's largest automobile company, has developed the Nano, the cheapest car in the world.
The case focuses on the t. As a follow-up to Tuesday’s post about the majority-minority public schools in Oslo, the following brief account reports the latest statistics on the cultural enrichment of schools in Austria.
Vienna is the most fully enriched location, and seems to be in roughly the same situation as Oslo. Many thanks to Hermes for the translation from ashio-midori.com Jesus and Nicodemus: 1: There was a man of the Pharisees, named Nicode'mus, a ruler of the Jews: 2: the same came to Jesus by night, and said unto him, Rabbi, we know that thou art a teacher come from God: for no man can do these miracles that thou doest, except God be with him.